Sklep Ipart
części samochodowe
Tarcze, hamulce
felgi - sklep internetowy sportwheels.pl


felgi - sklep internetowy ucando.pl

[B4 1Z] identification

ODPOWIEDZ
Awatar użytkownika
RS_TDI
Forum Audi 80
Forum Audi 80
Posty: 9
Rejestracja: 08 lut 2013, 10:59
Lokalizacja: Zagreb

[B4 1Z] identification

Post autor: RS_TDI » 01 kwie 2013, 00:37

Since I don't get Polish very well I decided to post it here. Please don't get me wrong if the same thread already exists. I would like to ask which reference should I look in vag com when I connect it to my car. Here is engine ID so if someone can tell me what to use, All 1z, D08 or D09.
Obrazek
Ostatnio zmieniony 01 kwie 2013, 08:13 przez RS_TDI, łącznie zmieniany 2 razy.

slawek5t
Forum Audi 80
Forum Audi 80
Posty: 69
Rejestracja: 21 lis 2012, 01:38
Lokalizacja: Bytów

Post autor: slawek5t » 01 kwie 2013, 00:45

all 1z :)
Golf III TDI 1Z+ '96r. Super chip by Kostrz ;)

Awatar użytkownika
RS_TDI
Forum Audi 80
Forum Audi 80
Posty: 9
Rejestracja: 08 lut 2013, 10:59
Lokalizacja: Zagreb

Post autor: RS_TDI » 01 kwie 2013, 00:47

OK thanks for quick reply....what are D08 and D09?
If it's all 1Z this is timing graph
Obrazek
Another question is: is timing related with car performance or only withengine start (cold start)?

Awatar użytkownika
Ganimadeus
Forum Audi 80
Forum Audi 80
Posty: 726
Rejestracja: 17 lut 2012, 11:17
Lokalizacja: Lublin

Post autor: Ganimadeus » 01 kwie 2013, 01:17

I don't believe tdi timing - reason? If u have a wrong temp sensor results could be incorrect. Always look at numbers :D

If Injection angle will be less than ~47-55 :
- a little weaker and fuel cunsumption will increase
- problem with start when is cold / smoke :d
- engine's sound will be softer

If Injection angle will be less than ~47-55 :
- a little bit stronger
- engine's sound will be characteristically harder

If u don't have any problems with cold start, power etc. u musn't fix it <ok>

Awatar użytkownika
RS_TDI
Forum Audi 80
Forum Audi 80
Posty: 9
Rejestracja: 08 lut 2013, 10:59
Lokalizacja: Zagreb

Post autor: RS_TDI » 01 kwie 2013, 01:25

How do I know if the angle is correct? The graph is same when engine is warm enough. Exactly what you said is happening...white smoke when it's cold, "softer sound" and little bit higher fuel consuption ;)

Awatar użytkownika
Ganimadeus
Forum Audi 80
Forum Audi 80
Posty: 726
Rejestracja: 17 lut 2012, 11:17
Lokalizacja: Lublin

Post autor: Ganimadeus » 01 kwie 2013, 12:05

RS_TDI pisze:How do I know if the angle is correct? The graph is same when engine is warm enough. Exactly what you said is happening...white smoke when it's cold, "softer sound" and little bit higher fuel consuption ;)
On your ss from vag BS groupe 000 2nd position - 44 is a little bit less from good :] But remember fix injection angle only at warm enginge min 80C at vag because at cold engine injection angle is bigger than warm engine and it decreases with temp. to correctly value.

47-55 is correctly value ;] Do u know how to fix it?

Awatar użytkownika
RS_TDI
Forum Audi 80
Forum Audi 80
Posty: 9
Rejestracja: 08 lut 2013, 10:59
Lokalizacja: Zagreb

Post autor: RS_TDI » 01 kwie 2013, 12:42

Oh that 44 is down next to fuel temp...I got that. Now i need to move the pump little bit "vor" right?

Awatar użytkownika
Ganimadeus
Forum Audi 80
Forum Audi 80
Posty: 726
Rejestracja: 17 lut 2012, 11:17
Lokalizacja: Lublin

Post autor: Ganimadeus » 01 kwie 2013, 12:48

Yeap you need key 13mm. Remember - only loosen ;]

Awatar użytkownika
RS_TDI
Forum Audi 80
Forum Audi 80
Posty: 9
Rejestracja: 08 lut 2013, 10:59
Lokalizacja: Zagreb

Post autor: RS_TDI » 01 kwie 2013, 13:43

OK, I'll try and then show results....thanks a lot!

ODPOWIEDZ

Wróć do „Silniki TDi”


opony samochodowe hamulce
felgi - sklep internetowy sportwheels.pl części samochodowe ucando.pl
części samochodowe iparts.pl
Prilo.com - Transport międzynarodowy samochodów
Tooles.pl - Sklep z elektronarzędziami
Pilarki akumulatorowe Stiga